How To Reset My Garbage Disposal?

How To Reset My Garbage Disposal

You may not know this but your garbage disposal is a breeding ground for bacteria and other harmful micro-organisms. This causes an unpleasant odor to emanate from the drain which can be difficult to eliminate with just bleach or vinegar alone. In order to keep your garbage disposal healthy, it is important that you perform regular maintenance on it by clearing out any food particles that have accumulated in the blades and disposing of them properly.

So in this post, I will be discussing and answering your question of how to reset my garbage disposal so read on…

How To Reset My Garbage Disposal?

In order to reset our garbage disposal unit, we first need to determine what is preventing it from switching on.

The most important reason why a garbage disposal unit would be unable to switch on is because the circuit breaker has been tripped. In order to restore the power supply, switch off your main house circuit breaker and then return it back to its original position.

If this does not work, check the manual release mechanism of your garbage disposal unit by pressing and holding it for a few seconds before releasing it again .

Typically, if you do this three times in a row , your disposal will reset itself.

This is because there may have been some residual energy still contained in the motor of your appliance which caused it to break down as soon as you switched it off.

However, if the resetting process does not work for you, there are a number of other things that can be done to get rid of the odor emanating from your disposal unit.

These include the following:

1. Ice And Salt

If your garbage disposal is unable to switch on, you can try filling the sink with cold water before throwing in a handful of ice cubes and then adding three or four teaspoons of salt into it .

Once this occurs, turn the garbage disposal unit back on for two minutes before switching it off again. After letting this mixture sit in your drain for about ten minutes, repeat the whole resetting procedure by pressing and holding down the manual release mechanism located near your appliance.

2. Baking Soda And Vinegar

If you have baking soda at home, sprinkle some of it directly down your drain while simultaneously pouring some vinegar after it .  This will cause a chemical reaction which will rid your drain of any odor.

3. Lemon Peels

Another effective home remedy for ridding your garbage disposal unit of foul odors is to throw some lemon peels into it while running the hot water tap to clear out any other debris .  The citric acid found in lemons will clean off all the grime and leave behind a fresh smell. 4. Boiling Water Yet another effective method for clearing out any lingering food particles from your garbage disposal unit is by filling up half a cup with boiling water before pouring it down the drain .

5. Cleaning Out The Blades

After you have successfully performed one of these procedures, try cleaning out the blades using either an old toothbrush or a special blade cleaner that can be purchased from any hardware store.  Using a toothbrush, scrape off any bits of food and debris that may have adhered to the blades before rinsing them with some cold water.

If you are still worried about the foul odor emanating from your sink after performing one of these methods then you can be assured that these odors are not toxic. They are only caused by excess remnants of food particles which form around the metal

The following steps will not only prevent odors from accumulating, but also help prevent clogs! To learn how to clear out debris from your blades and dispose of them properly, read below:

Step  1:  Turn off Water Supply.

Your garbage disposal is connected to your sink’s drain so it ensures that you always have access to water without needing a separate line for your disposal. However, if you are performing maintenance on the unit, blocking the drain is essential in preventing anything from falling into your disposal and causing an unpleasant odor or issue with clogs. To turn off your water supply, simply move the small switch under the sink. This will allow you to clean around your blades safely without any splashing or risk of electrocution.

Step 2: Remove Unit

If the switch does not work or you just want more room to maneuver while cleaning, then removing the unit will provide greater access for cleaning and allow you to replace your disposal more easily if need be. In order to remove the unit, simply locate the large clamps that hold it in place and twist them counterclockwise for a secure hold.

Step 3: Unplug Unit

Before removing the unit from its clamps, you will want to shut off power by unplugging the unit from under your sink. This ensures that you do not accidentally cut any electrical lines or damage sensitive components while handling it.

Step 4: Remove Disposal

Once everything is secure and ready, begin pulling gently on the disposal unit itself until it comes loose from its position. Be careful as you pull since there may still be water around the base which can potentially cause your garbage disposal to slip out of your hand and break if mishandled.

Step 5: Clean Drain

Once you have removed your disposal, you should take this time to clean out the area around your sink and how it connects with your drain. However, if there is still water in the unit itself and it has not been flushed for a while, we recommend cleaning that first since it can easily clog. To flush out any residue or sediment from inside the disposal’s chamber, simply turn on your faucet and let water flow through it for 30 seconds before turning off again.

Step 6: Wipe Out Chamber

After flushing out any built-up sediment or debris from inside of your unit including the blades themselves, use a rag to wipe down all surfaces surrounding your garbage disposal. This ensures that the entire unit is free of any material and debris which could cause future clogs or unpleasant odors.

Step 7: Reinstall

Once you have cleaned your disposal, unplug it from under your sink before carefully reinserting it into place. Be careful not to twist the clamps on the unit too strenuously as this can affect its position. We recommend checking whether its off-center by looking at the area where the drainhole lines up with your sink’s opening and comparing them so you can center everything evenly during installation for a more secure hold.

Step 8: Plug In Lastly

we recommend plugging back in your garbage disposal so that it returns to normal operation and you can turn on water flow again to flush any remaining water from inside of the unit.

If you follow these steps regularly then your garbage disposal will function properly without any issues.

How To Reset My Garbage Disposal

Where is my garbage disposal reset button?

The Garbage Disposal Reset button is usually located inside the unit somewhere. If you cannot figure out where your reset button is, then please refer to the manual that came with your disposal for information on how to deactivate it and turn it back on. Or if you do not have a manual or cannot find one, then our team can help assist you through email or telephone as well!

Do garbage disposals have a reset?

Yes! Please be sure that you have reset your button in order to resume normal disposal. If your unit starts to malfunction, then please refer to our list of common problems and fixes below:

Why can’t I reset my garbage disposal?

One of the key reasons as to why one cannot reset garbage disposal is due to an electrical malfunction. The reset button requires a certain amount of current and voltage in order to turn back on. So if you have power but do not hear any clicking noise when pressing said button, then that means your disposal is having trouble getting started again.

Another reason garbage disposal won’t reset is because it has become jammed. If your unit is unable to rotate under its own force, then this means that it may be experiencing issues with jamming.

How do I reset my Grindsmart garbage disposal?

Reseting grindsmart garbage disposal requires you to unplug the unit for at least 30 seconds. Once you have done so, plug it back in and turn on water flow again to flush any remaining water from inside of your disposal.

Further, you can reset grindsmart garbage disposal by manually turning the ring at the bottom to reset it. To do this, use a screwdriver and turn the floating ring until you hear a click.

References : How to Fix a Garbage Disposal

Noah Burns

I am Noah Burns- The Guy behind mybestsix.com. I love to experiment and test new products to create informative contents for readers like you. I aim to make this site a leading source of information and reviews to help consumers make more informed buying decisions.

Recent Posts