How To Increase Hot Water Pressure In Kitchen Sink?

How To Increase Hot Water Pressure In Kitchen Sink

I’ve been looking for a solution to my problem with the water pressure in my kitchen sink. I have a decent-sized house and only one bathroom, so when it comes time for dishes or washing up, there is always someone waiting in line. In an attempt to make the process more efficient, I’ve removed all but one of our sinks from downstairs and put them upstairs in the kitchen.

This leaves me with two options: either wait for hot water from downstairs or go without because nobody can use any other faucet while they are using mine.

How To Increase Hot Water Pressure In Kitchen Sink

One thing to look at is how low your pressure tank sits in relationship with your incoming cold water line. If it is too high, then you will have a harder time getting enough back pressure to get good pressure at your fixtures. Most tanks are adjustable, but be sure to fill it with water so that you don’t run the risk of getting a faulty reading on your gauge.

Another thing to look at is how long the line is between the tank and where the cold water enters your house. This also should not be too high and if it is too long of a run, the volume of water going through will be decreased which also decreases your pressure. It is possible to add a larger line called a “Bigger Hot Water Line”, but at $100-$150 for this luxury, you might as well just get the pressure tank adjusted because that will make more of a difference in the end.

Another thing to fix is what they call “Stiffening up”. Stiffening up means that your water line gets smaller and smaller as it goes back towards your house. This is done on purpose so that when you have just one faucet open, there isn’t some major pressure drop throughout the house.

How To Increase Hot Water Pressure In Kitchen Sink

If you don’t like the sound of this, try and find a way to remove this loop or “Tee-Off” from your cold water line feed.

The last thing that should be looked at is your toilet shut off valve. It might seem obvious, but most people think about the obvious things first. A great way to find out if this is the cause of your problem is to shut off all water in your house and try turning the faucets on again. If you now get full pressure from every faucet, then you know that it is a faulty toilet shut-off valve somewhere in the house.

The easiest thing to do would be to open up the access panel under your toilet and check out if you can see anything wrong. If not, try replacing the rubber washers inside (you may need a small pair of channel locks as well). If

you still can’t find anything wrong, then the best thing to do would be to replace it with a new one. Toilet shut off valves are super cheap these days and probably cost less than $10 at your local home improvement store.

The last thing I want to mention is to check out your water meter if you haven’t already. Not to scare anyone, but there are some people that claim that you should be able to remove the face of your meter without having it turn off. This is not true at all and if you see it, call a plumber ASAP so he can come out and replace your meter with one that has a built-in shut off valve inside. If you have a meter that can be turned off, then try to find the shut-off tool which is sometimes buried underneath some grass in your garden or stuck behind an abandoned flower pot.

I hope I was able to help some of my readers with this article and remember, don’t get too discouraged if you run into problems as there are always solutions. Good luck with everything and remember to ask questions if, after looking at these tips, you still need some help!

If this still doesn’t solve your problem, it might be time to call in a professional!

Why is my hot water pressure so low?

One of the reasons hot water pressure is so low in your kitchen sink could be a bad pressure-reducing valve.

Your pressure-reducing valve is located in the cold water feed line before it enters your house and serves to limit the amount of force on incoming water so that you won’t have any damage at your plumbing fixtures or break things like the faucet aerator.

The problem is that these valves are made to work within a very close range of pressures and when the pressure gets too high, they can either

  • not turn on at all – which means no water for you, or
  • open up so much that it causes major problems like low hot water pressure.

The best way to tell if this is your problem is to listen at a faucet or look for a water meter.

If you hear the water running out of the tap and there isn’t any water coming out of another faucet in the house, then this might be your source of low hot water pressure. If you find that there actually isn’t any water coming out of the tap and your water meter is running, this could mean that you have a problem with either the pressure-reducing valve or the cold water feed going into your house.

If it is just a faulty pressure-reducing valve, then replacing it should solve your low hot water pressure problems.

If it is the cold water feed, then this will be a much more difficult fix and might mean that you have to replace almost all of your plumbing from the street to your house.

Call an expert plumber for high hot water pressure problems in your home.

What can cause low hot water pressure?

Well, there are a few things that can cause low hot water pressure. First, you should check to make sure your tank is full. Insufficient tank water levels will restrict the water flow and not supply enough hot water for simultaneous demands.

Check where your cold water line comes into the house, it shouldn’t be before your internal plumbing distribution valve. If it is, this could be restricting the water flow and causing low hot water pressure since your internal plumbing distribution valve isn’t able to do its job.

What can cause high hot water pressure?

High hot water pressure can be caused by a lot of things, some of which are easy fixes and others that might require professional help.

If you have low water pressure in your shower, then you probably need to replace your internal plumbing distribution valve with a new one that has the correct flow rates for your house.

Also, check your toilets as well and make sure they aren’t constantly running by putting dye tablets or food coloring in them once a month.

You might be wasting a lot of water every day and not even know it!

If your pressure problem isn’t in the house, you should check to see if your pressure-reducing valve is still working properly on the street side.

Sometimes roots from trees can get into the service line and clog up the pressure-reducing valve. If this is the case, you might need to have a professional come out and remove these roots and replace the pressure-reducing valve.

High hot water pressure can also be caused by a buildup of calcium and magnesium deposits in your plumbing system, especially on your internal plumbing distribution valves.

This is because these minerals get mixed in with the water and as the water sits in your plumbing, it evaporates causing these deposits.

If this is what is causing your high hot water pressure problems then you should call a plumber to come out and clean up the insides of all your internal plumbing valves to get rid of these deposits.

Do I need a plumber for low hot water pressure?

You might need the help of a professional plumber if you aren’t able to solve your low hot water pressure problem on your own. Some issues, like long-term high hot water pressure problems or a bad internal plumbing distribution valve, will require the help of someone with experience in these matters.

A good plumber will be able to come up with the best solution for your specific low hot water pressure problems and get them fixed quickly, so you never have to worry about that household issue again!

How do I fix low hot water pressure in my kitchen sink?

In order to fix low hot water pressure in your kitchen sink, you need to check the faucet itself first.

If there is anything restricting the flow of water, like a buildup of scale or a clog in the aerator, then a plumber will need to come out and remove these buildups.

You can do this yourself by soaking a rag with vinegar and wrapping it around the aerator to soak overnight.

This should loosen up any scale or clogs so you can remove them yourself.

If this doesn’t work, then call a plumber because there might be a bigger problem that requires professional help.

You might need the help of a professional plumber if you aren’t able to solve your low hot water pressure problem on your own.

Some issues, like long-term high hot water pressure problems or a bad internal plumbing distribution valve, will require the help of someone with experience in these matters.

If you’re experiencing low hot water pressure, it could be because of a number of reasons. But before calling for professional help, make sure to check the faucet itself and see if there is anything restricting the flow like a buildup of scale or clogs in your aerator. If this doesn’t work, then call a plumber because there might be something more serious going on that requires professional attention. A good plumber will come up with the best solution for your specific problem and get them fixed quickly so you never have to worry about that household issue again!

References: How to Troubleshoot Low Hot Water Pressure on a Single Handle Kitchen Faucet

Noah Burns

I am Noah Burns- The Guy behind mybestsix.com. I love to experiment and test new products to create informative contents for readers like you. I aim to make this site a leading source of information and reviews to help consumers make more informed buying decisions.

Recent Posts